Monthly Archives: November 2012

Placing Dirt With a Telebelt

Placing Dirt With a Telebelt

Placing dirt can be a problem. Depending on your area, you could be dealing with clumps, stumps and lumps, among other things.  Moisture content can also be your enemy.  Here are a few tricks.

If you are using the aluminum Front End Loader Hopper (part # A306000), try putting 2×4 blocks under the front pads. This will raise the discharge end of the hopper and expose more belt to take the dirt out and reduce “bridging.” You will have to tie the front of the hopper down to the rail, to keep the blocks from falling out.

This shows a Front End Loader Hopper with an electric vibrator (part # A309849) installed, powered from the accessory plug on the Telebelt.  The operator has also raised the back of the hopper to expose more belt.  Note the chain and binder in place of the rear pin.

Also note the feeder is set up with the legs down.  This is the best way to keep spillage from jamming the tail pulley. Some operators of the small loaders complain they can’t see in the hopper.  They’ll get over it.

The best hopper to use with large loaders is the 3-Yard Hopper (part # A300042).  When using this hopper, keep the bottom of the skirts even with the top of the concrete hopper.  Don’t lower the skirts into the hopper, as that blocks the flow.  When the lower hopper fills, flow will stop.

 

 

View at discharge:  The ideal setup is the 3-Yard Hopper feeding a Low Profile hopper (part # A306001).  The transfer opening is large enough, plus you are not beating the concrete hopper to death.

 

 

 

Side view of Low Profile Hopper under 3-Yard Hopper.

 

 

 

 

 

 

 

An optional hopper grate (part # A309979)  is available for the 3-Yard Hopper.  It is strong enough so loaders can break up clumps.

 

 

 

 

 

It’s hinged, on the front and has notched legs in the
rear to set the angle of the grate.

Putzmeister Boom Valve Coil Tips

I have a little more homework and Info for you guys.

Over the years we all have had issues with setting and adjusting the boom speeds, either to fast or to slow, the function can feel rough or jerky or even black and white. Some have tried to repeatedly adjust the boom speeds with the Teleteach buttons or battery to no good result. If you need to constantly teach the remote you generally have a remote issue, other than oil temp variance the settings should stay relatively the same, week to week.

But there is another option you can easily look at for these types of symptoms.

The joystick is communicating to the coil on the boom valve, the coils can wear out, as they draw more Amps the range of motion changes, thus the need to adjust from time to time.

The plunger spool’s that the coil’s drive can also get sticky or gummed up over time. The images below will show you how to remove and clean the spools, test the coils, and look for issues. The coils are the same from valve to valve, so they can be moved around. BUT BEWARE, on units equipped with EBC this is not advisable, the computer is set to work with the coil and valve matched, adjustments to the EBC programming might need to be reset if coils are changed or moved around.

The leading problem we have with Mother Boards on 24 V systems is over Amping the fuse. If an outrigger or Boom coil is bad it can draw high amps and blow the fuse.  DO NOT PUT IN A BIGGER FUSE, RUN THE FUNCTION MANUALY AND FIX THE ISSUE.

 Other issues that can give you problems with these spools and other components on the unit are cheap oil, dirty oil, water in the oil, and high “TAN” numbers. These all lead to corrosion and sticky components all over the unit. Phantom issues that come and go are usually related to the oil and its condition. Do oil sample testing to ensure the condition of your oil. Oil that has water in it looks milky ONLY after it has become saturated with to much water, clear oil in the sight gauge can still have to much water in it. The only way to know for sure is to have it tested.

 

I hope this helps and brings out even more questions, please feel free to ask online or call PM CSG at 1-800-890-0269, or myself at 360-600-5695, or reach me by email at woodsa@putzam.com.

 

As always, be safe and keep the rubber side down.

Travelteck

 


PICTURE 1:
Coils are located behind the Boom valves. All the coils on a unit are the same, they can be swapped if needed.

Example: the Coil for the Boom / Outrigger is having issues, the Coil from the B arm could be used to swap with the Boom / Outrigger to get through a job.

Units with EBC rely on adjustments to compensate for coil resistance. On unit’s equipped with EBC you can change coils but EBC might need to be readjusted for the new coil. Without EBC there would not be an issue, but swapping coils to diagnose is not recommended on functioning EBC units.

High resistance values or shorted coils are one of the leading killers of Motherboards, NEVER over amp a fuse to make a function work even if it is for a “short time”, the motherboard will become the next fuse. Remember, everything you turn on with an electrical switch can be run MANUALY.